To make your Check’In 2 operational, it's important to follow all the steps outlined below:
Getting Started with the Check’In Pro Application
1 Download our Check’In Pro application from App Store or Play Store.
💡 Do not insert the batteries into your Check’In 2 sensor yet! You will be prompted to do so later during the installation process.
2 Open the Check’In Pro application. Enter your email address and your password, then tap on "Connect". If you don't have an account yet, ask the administrator of your organization to create one for you.
3 Once you are in the main menu of the application, tap on the red button "+".
4 Scan the QR code located at the back of your Check’In 2, below the battery compartment, so that it is recognized by your application.
5 Make sure that the IMEI, i.e., the serial number of the Check’In 2, is correct. If so, tap on "Continue".
6 Define the name and the type of use of your Check’In 2, as well as the type of door on which the sensor will be installed.
7 Select whether it is a vacant or occupied space.
8 Your Check’In 2 is now configured on our server. When the "Successful Activation" page appears, tap on "Got it".
Setting up the device
It's time to install your device! Your application displays the list of steps to follow. By tapping on one of them, you can watch a video explaining the steps to follow. Here are all the steps:
1 Insert the batteries respecting their polarity (positive and negative sides), then assemble the support of your Check’In 2 as illustrated in the application.
2 Using the degreasing wipe included in the Check’In box, clean the surface of the door where you will install your device. It should be located about 10 cm below the door lock.
3 Remove the protective films from the two adhesives of the Check’In 2, then stick the device on the door. Keep your hand pressed on the Check’In 2 for 15 seconds to ensure adhesion of the casing to the door.
Activating the device
1 Once the Check’In 2 is installed on your door, it will automatically connect to the 4G LTE-M or NB-IoT network.
💡 Be patient, this may take up to 10 minutes!
💡 If, after this time, your Check’In 2 does not emit a white light, reset it. To do this, press the button located on the right side of the Check'In 2 for about 9 seconds. The LED will light up in red and you should then release the button. You will hear a beep, indicating that the Check’In 2 will be reset and restarting. If you do not hear a beep, repeat the process.
💡 You have the option to background the installation in order to proceed with the installation of other Check'In. Once the connection has been established, the 📶 icon will turn green. Tap on the sensor's card to resume the installation process.
2 It is now time to activate the sensors of your Check’In 2. To do this, and following the instructions in the application, quickly press the button on the right side of the Check’In 2 twice. You will hear a beep, indicating that the sensors are activated. The Check’In 2 will automatically start the calibration process.
💡 Be careful not to touch your door while the Check’In 2 is calibrating!
3 Follow the various detailed steps in the application (open the door, close the door...).
Address and Emergency Contacts
1 In the application, and once the above steps are completed, add the postal address where the Check’In 2 is installed.
2 Once done, you have the option to transfer access rights to your client. If you decide to do so, the person to whom you transfer the rights will receive an email inviting them to take possession of the Check'In 2 access.
💡 They will need to accept the access request for you to no longer be the administrator of the Check'In 2.
3 You can now add up to 2 emergency contacts by tapping on "+ Add a contact". Fill in the requested information (specify if it is an on-call number or not), then tap on "Validate".
Your Check’In 2 is now installed and operational! 🎉